Nov 20, 2026

# Live visualization and data acquisition with LabJack

> The easiest way to stream LabJack T-Series data into live plots on macOS and Windows. No code required.

[Written by **Patrick Dotson**](https://www.linkedin.com/in/patrick-dotson/)

![A live plot of a LabJack thermocouple warming in a hand, beside the read task that streams it](https://synnax.nyc3.cdn.digitaloceanspaces.com/docs/blog/labjack-software/hero/5ed40fab8cde/window-light.webp)

[LabJack](https://labjack.com/) makes some of the best low-cost data acquisition devices on the market. They’re reliable, have lots of different I/O, and can hit high enough sample rates and fidelity for most needs, without splurging on more expensive hardware.

Unfortunately, the software for working with LabJack devices is adequate at best. If you want an out-of-the-box way to collect data, you can use [LJLogM](https://support.labjack.com/docs/ljlogm-windows-only) and [LJStreamM](https://support.labjack.com/docs/ljstreamm-windows-only). These tools work, but they’re unintuitive, not very pretty, and Windows only. On a Mac, you’re out of luck if you want something that doesn’t require you to write code. LabJack’s own advice is to [run them in a Windows virtual machine](https://labjack.com/blogs/news/logm-and-streamm-on-macos-with-parallels). You’re also pretty out of luck if you want to do no-code control.

We built [Synnax Desktop](https://docs.synnaxlabs.com/blog/introducing-synnax-desktop) to be one of the best free tools for working with any [T-Series](https://support.labjack.com/docs/t-series-datasheet) LabJack device. Fast, reliable, and intuitive data streaming and [control](https://docs.synnaxlabs.com/reference/hardware/labjack/write-task) are only a few clicks away. It runs on macOS and Windows, automatically finds your device, and gives you tons of flexibility for the experiments you want to run.

In this walkthrough, we’ll show you how to connect a LabJack T7, then acquire and visualize data from a thermocouple. Got a T4 or a T8? The steps are nearly the same, and we’ll call out the differences along the way.

## What you need

* A LabJack T4, T7, or T8, connected over USB or Ethernet. The T7-Pro also works over Wi-Fi.
* A type K thermocouple. The T4 has no thermocouple support, so use any other analog sensor with it instead.
* A Mac with Apple silicon, or a Windows PC.
* [Synnax Desktop](https://docs.synnaxlabs.com/reference/get-started/install-desktop).

The steps are the same on any T-Series device. The models differ in how they read thermocouples:

| Model | Thermocouples | How the task reads them                                    |
| ----- | ------------- | ---------------------------------------------------------- |
| T4    |               | Other sensors, as analog inputs                            |
| T7    |               | Polled, since the T7 can’t stream its cold-junction sensor |
| T8    |               | Streamed at 250 Hz or less, on isolated inputs             |

## Step 1Wire up the thermocouple

On a T7, connect the yellow (positive) lead to `AIN0` and the red (negative) lead to `GND`:

Using a T8? Its inputs are differential, so connect yellow to `AIN0+` and red to `AIN0-` instead.

## Step 2Install Synnax Desktop

1. Install the [LJM library](https://support.labjack.com/docs/ljm-software-installer-downloads-t4-t7-t8-digit) from LabJack. Desktop uses it to talk to your device.
2. [Install Synnax Desktop](https://docs.synnaxlabs.com/reference/get-started/install-desktop) and open it.
3. Select **New project**, give it a name, and select **Create**.

Desktop runs the Synnax Driver, Synnax Core, and Synnax Console together on your computer:

## Step 3Connect the LabJack

The Driver finds LabJack devices on its own by scanning through LJM: over USB every 5 seconds, and over Ethernet and Wi-Fi every 50 seconds. A networked device can take up to a minute to appear.

1. Open the devices toolbar from the bar on the left.
2. Select **Connect device** , then select **LabJack hardware**. The list shows every LabJack that the scans found, each named after its model and the last four digits of its serial number, like `LJM_dtT7-7383`.
3. Select **Configure** next to your T7.
4. Give it a **Name**, like `Lab T7`, and an **Identifier**, like `t7`. The identifier goes in front of every channel on the device, so your thermocouple channel will be `t7_AIN0`.
5. Select **Save and create read task**.

[](https://synnax.nyc3.cdn.digitaloceanspaces.com/docs/blog/labjack-software/connect/f3c04645a5e7.mp4#t=0.001)

Don’t see your device, or can’t connect to it? Over USB, only one program can open a LabJack at a time. Close Kipling and any other LabJack software, then wait for the next scan.

## Step 4Read the thermocouple

The new read task has one analog input channel, on `AIN0`. To read it as a thermocouple:

1. Set **Channel type** to **Thermocouple**. The thermocouple type defaults to K, and cold-junction compensation defaults to the device’s internal temperature sensor.
2. Set **Temperature units** to **Celsius**.
3. Select the start button. The status changes to “Started task”, and the task samples `AIN0` at 10 Hz.

[](https://synnax.nyc3.cdn.digitaloceanspaces.com/docs/blog/labjack-software/read/ab580f0713f2.mp4#t=0.001)

On a T4, skip the first two steps and leave the channel as **Analog input**. It reads volts instead of degrees.

## Step 5Plot it live

1. At the top right of the task, select **Plot channels** . A line plot of `t7_AIN0` opens, showing the last 30 seconds.
2. Hold the thermocouple’s junction, the welded tip, in your hand. The reading climbs several degrees within 30 seconds.

[](https://synnax.nyc3.cdn.digitaloceanspaces.com/docs/blog/labjack-software/plot/66268ee36ff6.mp4#t=0.001)

The task sends its samples to the Core at the 5 Hz stream rate, two per channel each time, so the plot updates five times a second.

## Step 6Record and export

**Data saving** is on by default, so the Core stores every sample the task reads, and there’s no separate logging step. To export a span of it as a CSV:

1. Hold **Alt** (**Option** on macOS) and drag across the plot to select a region.
2. Right-click the selection and select **Download region as CSV** .

[](https://synnax.nyc3.cdn.digitaloceanspaces.com/docs/blog/labjack-software/export/8d8dd8626453.mp4#t=0.001)

To find this test again later, select **Create range from selection** instead. A [range](https://docs.synnaxlabs.com/reference/ranges) is a named span of time, so you can search for it and plot its data again.

## Next steps

From here, you can build on the same project:

* [Schematics](https://docs.synnaxlabs.com/reference/visualize/schematics) -> build operator screens with live values and buttons.
* [Alarms](https://docs.synnaxlabs.com/reference/alarms) -> get notified when a reading goes out of bounds.
* [LabJack write tasks](https://docs.synnaxlabs.com/reference/hardware/labjack/write-task) -> drive the LabJack’s analog outputs and digital output lines.
* [LabJack read tasks](https://docs.synnaxlabs.com/reference/hardware/labjack/read-task) -> every read task option, in detail.

Try Synnax Desktop

Free for any use, including commercial use, up to 50 channels. On macOS and Windows.

[Download Synnax Desktop](https://github.com/synnaxlabs/synnax/releases/download/desktop/v1.2.0/Synnax-Desktop_1.2.0_aarch64.dmg) v1.2.0 for macOS

[Download Synnax Desktop](https://github.com/synnaxlabs/synnax/releases/download/desktop/v1.2.0/Synnax-Desktop_1.2.0_x64-setup.exe) v1.2.0 for Windows

![The Synnax Console](https://synnax.nyc3.cdn.digitaloceanspaces.com/docs/console/visualize/hero/fe9f93bc85d3/window-light.webp)
